mgv2000刷的r3300l镜像,结果不能联网,也刷不回盒子了,求助

版主: 论坛版主

回复
qfnuzlr
中学生
帖子: 56
注册时间: 04 11月 2018, 09:38

mgv2000刷的r3300l镜像,结果不能联网,也刷不回盒子了,求助

帖子 qfnuzlr » 14 9月 2019, 17:02

如题
看到盒子cpu一样 就刷了 结果 联网获取不到ip
要刷回盒子 进入不了线刷模式
ttl信息如下
DGXLX2:BL1:3cfee7:42a5ae;FEAT:ADFD318C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 97805

BL2 Built : 19:16:55, Jun 22 2018.
gxl gb679ae5 - yao.zhang@droid07

Board ID = 3, adc=224
GET GPIO_AO_4 VALUE:16-------
set gpio_ao_4 high
CPU clk: 1200MHz

DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz
bist_test rank: 0 23 03 43 2e 12 4b 20 00 40 34 13 55 24 03 45 31 11 52 22 02 43 33 10 57 650 - PASS

Rank0: 1024MB(auto)-2T-11
AddrBus test pass!
emmc 52M
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x013c0000, size: 0x00007600
Load bl301 from eMMC, src: 0x00018200, des: 0x01380000, size: 0x00002200
Load bl31 from eMMC, src: 0x0001c200, des: 0x10100000, size: 0x00019600
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x00047200
NOTICE: BL3-1: v1.0(debug):521e8c3
NOTICE: BL3-1: Built : 14:22:49, Jun 5 2018
NOTICE: BL31: GXL normal boot!
NOTICE: BL31: BL33 decompress pass
[Image: gxl_v1.1.3103-27cb61a 2018-07-11 13:57:47 xianghua.tan@droid12-sz]
efuse init ops = c5
efuse init hdcp = c, cf9=7
bl30: check_permit, count is 1
bl30: check_permit: ok!
chipid: 0 0 3 c c 0 2f b4 68 a0 0 c5 not ES chip
[0.526013 Inits done]
INsFO: BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR: Error initializing runtime service opteed_fast
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address = 0x1000000
INFO: BL3-1: Next image spsr = 0x3c9
scure task
at
orUt-!B
Fohitg h2 t0a1s5k .s0tar1t !(
9eblo w2 t0ask st2a0rt!1
- 11:14:09)

DRAM: 1 GiB
Relocation Offset is: 36eef000
gpio: pin GPIODV_25 (gpio 44) value is 1
register usb cfg[0][1] = 0000000037f61700
[CANVAS]canvas init
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
vpp: vpp_init
MMC: aml_priv->desc_buf = 0x0000000033edfac0
aml_priv->desc_buf = 0x0000000033ee1de0
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
init_part() 278: PART_TYPE_DOS
[mmc_init] mmc init success
dtb magic 5f4c4d41
Amlogic multi-dtb tool
Multi dtb detected
unified board, board id = 43
Multi dtb tool version: v2 .
Support 6 dtbs.
aml_dt soc: gxlx2 platform: p291 variant: 1g
dtb 0 soc: gxl plat: p211 vari: 1g
dtb 1 soc: gxlx plat: p261 vari: 1g
dtb 2 soc: gxlx plat: p265 vari: 1g
dtb 3 soc: gxlx plat: p265 vari: 2g
dtb 4 soc: gxlx2 plat: p291 vari: 1g
dtb 5 soc: gxlx2 plat: p291 vari: 2g
Find match dtb: 4
start dts,buffer=0000000033ee4610,dt_addr=0000000033f0c610
Amlogic multi-dtb tool
Multi dtb detected
unified board, board id = 43
Multi dtb tool version: v2 .
Support 6 dtbs.
aml_dt soc: gxlx2 platform: p291 variant: 1g
dtb 0 soc: gxl plat: p211 vari: 1g
dtb 1 soc: gxlx plat: p261 vari: 1g
dtb 2 soc: gxlx plat: p265 vari: 1g
dtb 3 soc: gxlx plat: p265 vari: 2g
dtb 4 soc: gxlx2 plat: p291 vari: 1g
dtb 5 soc: gxlx2 plat: p291 vari: 2g
Find match dtb: 4
parts: 12
00: logo 0000000002000000 1
01: recovery 0000000002000000 1
02: rsv 0000000000800000 1
03: tee 0000000000800000 1
04: crypt 0000000002000000 1
05: misc 0000000002000000 1
06: boot 0000000002000000 1
07: system 0000000040000000 1
08: cache 0000000020000000 2
09: params 0000000004000000 2
10: bootfiles 0000000020000000 2
11: data ffffffffffffffff 4
init_part() 278: PART_TYPE_DOS
eMMC/TSD partition table have been checked OK!
check pattern success
mmc env offset: 0x27400000
In: serial
Out: serial
Err: serial
board id is : 43
hpd_state=0
cvbs performance type = 7, table = 0
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-924: calc 9ea74ac4, store 9ea74ac4
_verify_dtb_checksum()-924: calc 9ea74ac4, store 9ea74ac4
dtb_read()-1046: total valid 2
dtb_read()-1113: do nothing
Amlogic multi-dtb tool
Multi dtb detected
Multi dtb tool version: v2 .
Support 6 dtbs.
aml_dt soc: gxlx2 platform: p291 variant: 1g
dtb 0 soc: gxl plat: p211 vari: 1g
dtb 1 soc: gxlx plat: p261 vari: 1g
dtb 2 soc: gxlx plat: p265 vari: 1g
dtb 3 soc: gxlx plat: p265 vari: 2g
dtb 4 soc: gxlx2 plat: p291 vari: 1g
dtb 5 soc: gxlx2 plat: p291 vari: 2g
Find match dtb: 4
wipe_data=successful
wipe_cache=successful
bmp pixel: 24
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3dc00000
[OSD]load fb addr from dts
[OSD]fb_addr for logo: 0x3dc00000
[CANVAS]addr=0x3dc00000 width=5760, height=2160
upgrade_step=2
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
[BL31]: tee size: 0
[KM]Error:f[keymanage_dts_get_key_device]L85:model key name is not exist
[KM]Error:f[_get_km_ops_by_name]L231:key model not know device 4
[KM]Error:f[key_manage_query_exist]L546:There isn't dts cfg for key[model]
[KM]Error:f[key_manage_query_size]L503:Fail in query key exist
boot_select kernel[0,3) recovery[3,10) factory[10,*)
boot_select current count=0
boot_select count=0
boot_select=kernel
rebootmode=cold_boot
Hit any key to stop autoboot: 0
(Re)start USB...
USB0: USB3.0 XHCI init start
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
** Bad device usb 0 **
** Bad device usb 1 **
** Bad device usb 2 **
** Bad device usb 3 **
card out
emmc/sd response timeout, cmd8, status=0x1ff2800
emmc/sd response timeout, cmd55, status=0x1ff2800
emmc/sd response timeout, cmd1, status=0x1ff2800
reading emmc_autoscript
594 bytes read in 3 ms (193.4 KiB/s)
## Executing script at 01020000
reading zImage
20498440 bytes read in 588 ms (33.2 MiB/s)
reading uInitrd
5447011 bytes read in 160 ms (32.5 MiB/s)
reading uEnv.ini
230 bytes read in 2 ms (112.3 KiB/s)
reading /dtb/meson-gxl-s905x-r3300l.dtb
27790 bytes read in 7 ms (3.8 MiB/s)
[KM]Error:f[keymanage_dts_parse]L261:dts: err(FDT_ERR_NOTFOUND) in find /unifykey.
libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND
[rsvmem] bl31 reserved memory set addr error.
## Loading init Ramdisk from Legacy Image at 13000000 ...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
Data Size: 5446947 Bytes = 5.2 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Amlogic multi-dtb tool
Single dtb detected
load dtb from 0x1000000 ......
## Flattened Device Tree blob at 01000000
Booting using the fdt blob at 0x1000000
libfdt fdt_path_offset() returned FDT_ERR_NOTFOUND
[rsvmem] bl31 reserved memory set addr error.
Loading Ramdisk to 339aa000, end 33edbd23 ... OK
Loading Device Tree to 000000000fff6000, end 000000000ffffc8d ... OK
fdt_instaboot: get header err

Starting kernel ...

uboot time: 4075776 us
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[ 0.000000] Linux version 5.0.0-aml-N1-BonusCloud-1-2+ (root@bonuscloud) (gcc version 7.4.1 20181213 [linaro-7.4-2019.02 revision 56ec6f6b99cc167ff0c2f8e1a2eed33b1edc85d4] (Linaro GCC 7.4-2019.02)) #2 SMP Mon Jun 3 12:46:43 CST 2019
[ 0.000000] Machine model: R3300-L
[ 0.000000] OF: reserved mem: failed to allocate memory for node 'linux,cma'
[ 0.000000] cma: Reserved 256 MiB at 0x0000000023800000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv0.2 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] random: get_random_bytes called from start_kernel+0xa8/0x3ec with crng_init=0
[ 0.000000] percpu: Embedded 23 pages/cpu @(____ptrval____) s54872 r8192 d31144 u94208
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: detected: ARM erratum 845719
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 220480
[ 0.000000] Kernel command line: root=LABEL=ROOT_EMMC rootflags=data=writeback rw console=ttyAML0,115200n8 console=tty0 no_console_suspend consoleblank=0 fsck.fix=yes fsck.repair=yes fsck.mode=force net.ifnames=0
[ 0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.000000] Memory: 585600K/896000K available (13758K kernel code, 1138K rwdata, 4452K rodata, 576K init, 759K bss, 48256K reserved, 262144K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] irq_meson_gpio: 110 to 8 gpio interrupt mux initialized
[ 0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000004] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000388] Console: colour dummy device 80x25
[ 0.000578] printk: console [tty0] enabled
[ 0.000611] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.000626] pid_max: default: 32768 minimum: 301
[ 0.000705] LSM: Security Framework initializing
[ 0.000760] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.000773] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[ 0.001771] ASID allocator initialised with 32768 entries
[ 0.001842] rcu: Hierarchical SRCU implementation.
[ 0.004400] smp: Bringing up secondary CPUs ...
[ 0.004815] Detected VIPT I-cache on CPU1
[ 0.004867] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[ 0.005293] Detected VIPT I-cache on CPU2
[ 0.005328] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[ 0.005730] Detected VIPT I-cache on CPU3
[ 0.005762] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[ 0.005816] smp: Brought up 1 node, 4 CPUs
[ 0.005867] SMP: Total of 4 processors activated.
[ 0.005876] CPU features: detected: 32-bit EL0 Support
[ 0.005885] CPU features: detected: CRC32 instructions
[ 0.006174] CPU: All CPU(s) started at EL2
[ 0.006194] alternatives: patching kernel code
[ 0.006910] devtmpfs: initialized
[ 0.011106] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.011136] futex hash table entries: 1024 (order: 4, 65536 bytes)
[ 0.018046] xor: measuring software checksum speed
[ 0.056179] 8regs : 2303.000 MB/sec
[ 0.096207] 32regs : 2831.000 MB/sec
[ 0.136240] arm64_neon: 2510.000 MB/sec
[ 0.136248] xor: using function: 32regs (2831.000 MB/sec)
[ 0.136265] pinctrl core: initialized pinctrl subsystem
[ 0.137418] NET: Registered protocol family 16
[ 0.137874] audit: initializing netlink subsys (disabled)
[ 0.138027] audit: type=2000 audit(0.136:1): state=initialized audit_enabled=0 res=1
[ 0.138822] cpuidle: using governor menu
[ 0.139197] vdso: 2 pages (1 code @ (____ptrval____), 1 data @ (____ptrval____))
[ 0.139221] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.140148] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.140862] Serial: AMBA PL011 UART driver
[ 0.158260] cryptd: max_cpu_qlen set to 1000
[ 0.224471] raid6: neonx8 gen() 1722 MB/s
[ 0.292511] raid6: neonx8 xor() 1571 MB/s
[ 0.360544] raid6: neonx4 gen() 1585 MB/s
[ 0.428592] raid6: neonx4 xor() 1480 MB/s
[ 0.496661] raid6: neonx2 gen() 1222 MB/s
[ 0.564695] raid6: neonx2 xor() 1231 MB/s
[ 0.632805] raid6: neonx1 gen() 755 MB/s
[ 0.700789] raid6: neonx1 xor() 865 MB/s
[ 0.768872] raid6: int64x8 gen() 1003 MB/s
[ 0.836864] raid6: int64x8 xor() 757 MB/s
[ 0.904945] raid6: int64x4 gen() 1083 MB/s
[ 0.972998] raid6: int64x4 xor() 768 MB/s
[ 1.041085] raid6: int64x2 gen() 724 MB/s
[ 1.109082] raid6: int64x2 xor() 609 MB/s
[ 1.177241] raid6: int64x1 gen() 478 MB/s
[ 1.245170] raid6: int64x1 xor() 443 MB/s
[ 1.245178] raid6: using algorithm neonx8 gen() 1722 MB/s
[ 1.245186] raid6: .... xor() 1571 MB/s, rmw enabled
[ 1.245193] raid6: using neon recovery algorithm
[ 1.245617] fbcon: Taking over console
[ 1.247331] vgaarb: loaded
[ 1.247595] SCSI subsystem initialized
[ 1.248020] usbcore: registered new interface driver usbfs
[ 1.248090] usbcore: registered new interface driver hub
[ 1.248159] usbcore: registered new device driver usb
[ 1.248697] pps_core: LinuxPPS API ver. 1 registered
[ 1.248720] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 1.248754] PTP clock support registered
[ 1.248983] EDAC MC: Ver: 3.0.0
[ 1.249784] Advanced Linux Sound Architecture Driver Initialized.
[ 1.251125] clocksource: Switched to clocksource arch_sys_counter
[ 1.251303] VFS: Disk quotas dquot_6.6.0
[ 1.251355] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.251430] FS-Cache: Loaded
[ 1.258550] NET: Registered protocol family 2
[ 1.259021] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes)
[ 1.259054] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 1.259151] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[ 1.259260] TCP: Hash tables configured (established 8192 bind 8192)
[ 1.259374] UDP hash table entries: 512 (order: 2, 16384 bytes)
[ 1.259407] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[ 1.259544] NET: Registered protocol family 1
[ 1.259882] RPC: Registered named UNIX socket transport module.
[ 1.259897] RPC: Registered udp transport module.
[ 1.259904] RPC: Registered tcp transport module.
[ 1.259911] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 1.260083] Unpacking initramfs...
[ 1.478499] Freeing initrd memory: 5316K
[ 1.479402] hw perfevents: enabled with armv8_cortex_a53 PMU driver, 7 counters available
[ 1.479758] kvm [1]: 8-bit VMID
[ 1.479771] kvm [1]: IPA Size Limit: 40bits
[ 1.480378] kvm [1]: vgic interrupt IRQ1
[ 1.480475] kvm [1]: Hyp mode initialized successfully
[ 1.591064] Initialise system trusted keyrings
[ 1.591257] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[ 1.596979] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.597327] FS-Cache: Netfs 'nfs' registered for caching
[ 1.597833] NFS: Registering the id_resolver key type
[ 1.597868] Key type id_resolver registered
[ 1.597876] Key type id_legacy registered
[ 1.597890] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 1.598120] FS-Cache: Netfs 'cifs' registered for caching
[ 1.598397] ntfs: driver 2.1.32 [Flags: R/W].
[ 1.598953] JFS: nTxBlock = 6664, nTxLock = 53316
[ 1.602465] SGI XFS with security attributes, no debug enabled
[ 1.603683] 9p: Installing v9fs 9p2000 file system support
[ 1.604020] ocfs2: Registered cluster interface o2cb
[ 1.604227] OCFS2 User DLM kernel interface loaded
[ 1.605657] gfs2: GFS2 installed
[ 1.687936] Key type asymmetric registered
[ 1.687960] Asymmetric key parser 'x509' registered
[ 1.688027] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244)
[ 1.688048] io scheduler mq-deadline registered
[ 1.688056] io scheduler kyber registered
[ 1.701300] meson_vid_pll_div_recalc_rate: Invalid config value for vid_pll_div
[ 1.704590] soc soc0: Amlogic Meson Unknown (Unknown) Revision 2a:e (c5:2) Detected
[ 1.708451] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 1.710293] Serial: AMBA driver
[ 1.710679] c11084c0.serial: ttyAML1 at MMIO 0xc11084c0 (irq = 10, base_baud = 1500000) is a meson_uart
[ 1.710845] serial serial0: tty port ttyAML1 registered
[ 1.711190] c81004c0.serial: ttyAML0 at MMIO 0xc81004c0 (irq = 15, base_baud = 1500000) is a meson_uart
[ 2.537964] printk: console [ttyAML0] enabled
[ 2.542864] c81004e0.serial: ttyAML2 at MMIO 0xc81004e0 (irq = 16, base_baud = 1500000) is a meson_uart
[ 2.560234] loop: module loaded
[ 2.560806] zram: Added device: zram0
[ 2.564032] libphy: Fixed MDIO Bus: probed
[ 2.565772] tun: Universal TUN/TAP device driver, 1.6
[ 2.571385] thunder_xcv, ver 1.0
[ 2.573684] thunder_bgx, ver 1.0
[ 2.576894] nicpf, ver 1.0
[ 2.580169] e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k
[ 2.585296] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[ 2.591210] igb: Intel(R) Gigabit Ethernet Network Driver - version 5.4.0-k
[ 2.598053] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 2.603622] igbvf: Intel(R) Gigabit Virtual Function Network Driver - version 2.4.0-k
[ 2.611336] igbvf: Copyright (c) 2009 - 2012 Intel Corporation.
[ 2.617441] sky2: driver version 1.30
[ 2.621367] VFIO - User Level meta-driver version: 0.3
[ 2.627231] dwc3 c9000000.dwc3: Failed to get clk 'ref': -2
[ 2.633143] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.637961] ehci-pci: EHCI PCI platform driver
[ 2.642378] ehci-platform: EHCI generic platform driver
[ 2.647737] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.653623] ohci-pci: OHCI PCI platform driver
[ 2.658065] ohci-platform: OHCI generic platform driver
[ 2.663997] usbcore: registered new interface driver usb-storage
[ 2.671187] mousedev: PS/2 mouse device common for all mice
[ 2.675542] i2c /dev entries driver
[ 2.681015] device-mapper: ioctl: 4.39.0-ioctl (2018-04-03) initialised: dm-devel@redhat.com
[ 2.687326] sdhci: Secure Digital Host Controller Interface driver
[ 2.692606] sdhci: Copyright(c) Pierre Ossman
[ 2.697134] Synopsys Designware Multimedia Card Interface Driver
[ 2.704025] meson-gx-mmc d0070000.mmc: Linked as a consumer to regulator.2
[ 2.709704] meson-gx-mmc d0070000.mmc: Linked as a consumer to regulator.1
[ 2.716587] meson-gx-mmc d0070000.mmc: Dropping the link to regulator.1
[ 2.723126] meson-gx-mmc d0070000.mmc: Dropping the link to regulator.2
[ 2.729981] meson-gx-mmc d0072000.mmc: Linked as a consumer to regulator.2
[ 2.736437] meson-gx-mmc d0072000.mmc: Linked as a consumer to regulator.1
[ 2.743265] meson-gx-mmc d0072000.mmc: Got CD GPIO
[ 2.774990] meson-gx-mmc d0074000.mmc: Linked as a consumer to regulator.4
[ 2.776296] meson-gx-mmc d0074000.mmc: Linked as a consumer to regulator.1
[ 2.783115] meson-gx-mmc d0074000.mmc: allocated mmc-pwrseq
[ 2.815657] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.816956] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.822317] meson-sm: secure-monitor enabled
[ 2.826149] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.832061] usbcore: registered new interface driver usbhid
[ 2.836751] usbhid: USB HID core driver
[ 2.840921] platform-mhu c883c404.mailbox: Platform MHU Mailbox registered
[ 2.848276] meson-saradc c1108680.adc: Linked as a consumer to regulator.3
[BL31]: tee size: 0
[ 2.858017] NET: Registered protocol family 17
[ 2.860586] 9pnet: Installing 9P2000 support
[ 2.864672] Key type dns_resolver registered
[ 2.869528] registered taskstats version 1
[ 2.872905] Loading compiled-in X.509 certificates
[ 2.878795] Btrfs loaded, crc32c=crc32c-generic
[ 2.890372] phy phy-d0078000.phy.0: Linked as a consumer to regulator.5
[ 2.893534] meson-drm d0100000.vpu: Queued 2 outputs on vpu
[ 2.896943] mmc1: mmc_select_hs200 failed, error -74
[ 2.898803] mmc1: new MMC card at address 0001
[ 2.902444] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 2.907748] mmcblk1: mmc1:0001 T22708 7.13 GiB
[ 2.912749] [drm] No driver support for vblank timestamp query.
[ 2.917919] mmcblk1boot0: mmc1:0001 T22708 partition 1 4.00 MiB
[ 2.923213] meson-drm d0100000.vpu: CVBS Output connector not available
[ 2.929624] mmcblk1boot1: mmc1:0001 T22708 partition 2 4.00 MiB
[ 2.935637] meson-dw-hdmi c883a000.hdmi-tx: Linked as a consumer to regulator.5
[ 2.948735] mmcblk1rpmb: mmc1:0001 T22708 partition 3 4.00 MiB, chardev (241:0)
[ 2.957570] mmcblk1: p1 p2
[ 2.979177] meson-dw-hdmi c883a000.hdmi-tx: Unsupported HDMI controller (0d0d:0d:0d)
[ 2.981453] WARNING: CPU: 3 PID: 67 at drivers/regulator/core.c:2054 _regulator_put.part.9+0xf0/0xf8
[ 2.990334] Modules linked in:
[ 2.993358] CPU: 3 PID: 67 Comm: kworker/3:1 Not tainted 5.0.0-aml-N1-BonusCloud-1-2+ #2
[ 3.001374] Hardware name: R3300-L (DT)
[ 3.005177] Workqueue: events deferred_probe_work_func
[ 3.010260] pstate: 80000005 (Nzcv daif -PAN -UAO)
[ 3.015003] pc : _regulator_put.part.9+0xf0/0xf8
[ 3.019574] lr : regulator_put+0x34/0x50
[ 3.023454] sp : ffff0000101b3910
[ 3.026731] x29: ffff0000101b3910 x28: ffff800034e04180
[ 3.031993] x27: 00000000ffffffed x26: 0000000000000001
[ 3.037254] x25: ffff0000123c9800 x24: 000000000000000f
[ 3.042515] x23: ffff0000101b39b8 x22: ffff800036054c10
[ 3.047776] x21: ffff000012315000 x20: ffff800034e04900
[ 3.053037] x19: ffff800034e04900 x18: 0000000000000400
[ 3.058299] x17: 0000000000000001 x16: 0000000000000019
[ 3.063560] x15: 0000000000000400 x14: 0000000000000400
[ 3.068821] x13: 0000000000000002 x12: 0000000000000001
[ 3.074082] x11: 00000000012b791d x10: 0000000000000000
[ 3.079344] x9 : ffff7e0000d38120 x8 : 0000000000000000
[ 3.084605] x7 : ffff800005303b00 x6 : ffff000012315688
[ 3.089866] x5 : 0000000000210d00 x4 : 0000000000000000
[ 3.095127] x3 : 0000000000000000 x2 : ffff800010228000
[ 3.100388] x1 : 0000000000000000 x0 : 0000000000000001
[ 3.105650] Call trace:
[ 3.108068] _regulator_put.part.9+0xf0/0xf8
[ 3.112293] regulator_put+0x34/0x50
[ 3.115830] devm_regulator_release+0x10/0x18
[ 3.120143] release_nodes+0x138/0x228
[ 3.123850] devres_release_group+0xa8/0x108
[ 3.128079] component_bind_all+0x1a8/0x2c0
[ 3.132217] meson_drv_bind_master+0x38c/0x490
[ 3.136615] meson_drv_bind+0x10/0x18
[ 3.140239] try_to_bring_up_master+0x21c/0x300
[ 3.144724] component_master_add_with_match+0xb4/0x100
[ 3.149898] meson_drv_probe+0xdc/0x140
[ 3.153695] platform_drv_probe+0x50/0xa0
[ 3.157661] really_probe+0x2b8/0x3d0
[ 3.161283] driver_probe_device+0x12c/0x148
[ 3.165510] __device_attach_driver+0xa8/0x158
[ 3.169908] bus_for_each_drv+0x64/0xc8
[ 3.173703] __device_attach+0xd8/0x158
[ 3.177499] device_initial_probe+0x10/0x18
[ 3.181638] bus_probe_device+0x90/0x98
[ 3.185433] deferred_probe_work_func+0x88/0xe0
[ 3.189921] process_one_work+0x1e4/0x368
[ 3.193886] worker_thread+0x268/0x4b0
[ 3.197595] kthread+0x128/0x130
[ 3.200787] ret_from_fork+0x10/0x1c
[ 3.204321] ---[ end trace deeb063726333f93 ]---
[ 3.208954] meson-dw-hdmi c883a000.hdmi-tx: Dropping the link to regulator.5
[ 3.215921] meson-drm d0100000.vpu: failed to bind c883a000.hdmi-tx (ops meson_dw_hdmi_ops): -19
[ 3.224602] meson-drm d0100000.vpu: Couldn't bind all components
[ 3.230655] meson-drm d0100000.vpu: master bind failed: -19
[ 3.239048] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 3.241551] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 3.249694] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f664 hci version 0x100 quirks 0x0000000002010010
[ 3.258464] xhci-hcd xhci-hcd.0.auto: irq 40, io mem 0xc9000000
[ 3.264546] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.00
[ 3.272475] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.279627] usb usb1: Product: xHCI Host Controller
[ 3.284456] usb usb1: Manufacturer: Linux 5.0.0-aml-N1-BonusCloud-1-2+ xhci-hcd
[ 3.291700] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 3.296967] hub 1-0:1.0: USB hub found
[ 3.300293] hub 1-0:1.0: 2 ports detected
[ 3.304519] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 3.309660] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 3.317245] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
[ 3.323853] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 3.331905] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.00
[ 3.340001] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 3.347158] usb usb2: Product: xHCI Host Controller
[ 3.351988] usb usb2: Manufacturer: Linux 5.0.0-aml-N1-BonusCloud-1-2+ xhci-hcd
[ 3.359232] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 3.364515] hub 2-0:1.0: USB hub found
[ 3.367815] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 3.376127] meson-gx-mmc d0070000.mmc: Linked as a consumer to regulator.2
[ 3.381725] meson-gx-mmc d0070000.mmc: Linked as a consumer to regulator.1
[ 3.388570] meson-gx-mmc d0070000.mmc: Dropping the link to regulator.1
[ 3.395065] meson-gx-mmc d0070000.mmc: Dropping the link to regulator.2
[ 3.403509] scpi_protocol scpi: SCP Protocol legacy pre-1.0 firmware
get_dvfs_info 002b
[ 3.421003] meson-gx-mmc d0070000.mmc: Linked as a consumer to regulator.2
[ 3.422275] meson-gx-mmc d0070000.mmc: Linked as a consumer to regulator.1
[ 3.429201] meson-gx-mmc d0070000.mmc: Dropping the link to regulator.1
[ 3.435666] meson-gx-mmc d0070000.mmc: Dropping the link to regulator.2
[ 3.444404] meson-gx-mmc d0070000.mmc: Linked as a consumer to regulator.2
[ 3.449044] meson-gx-mmc d0070000.mmc: Linked as a consumer to regulator.1
[ 3.455896] meson-gx-mmc d0070000.mmc: Dropping the link to regulator.1
[ 3.462385] meson-gx-mmc d0070000.mmc: Dropping the link to regulator.2
[ 3.469720] hctosys: unable to open rtc device (rtc0)
[ 3.474209] VDDAO_3V3: disabling
[ 3.477110] ALSA device list:
[ 3.480033] No soundcards found.
[ 3.483801] Freeing unused kernel memory: 576K
[ 3.519529] Run /init as init process
[ 3.556516] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 3.558416] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 3.561550] random: udevadm: uninitialized urandom read (16 bytes read)
[ 3.888371] random: fast init done
[ 6.255026] EXT4-fs (mmcblk1p2): mounted filesystem with writeback data mode. Opts: data=writeback
[ 6.765312] systemd[1]: System time before build time, advancing clock.
[ 6.882467] NET: Registered protocol family 10
[ 6.883169] Segment Routing with IPv6
[ 6.927880] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[ 6.940879] systemd[1]: Detected architecture arm64.
[ 6.946949] systemd[1]: Set hostname to <BonusCloud-Lite>.
[ 7.249084] systemd[1]: [/etc/systemd/system/systemd-udevd.service:31] Unknown lvalue 'IPAddressAllow' in section 'Service'
[ 7.355192] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 7.357089] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 7.364637] systemd[1]: Listening on LVM2 poll daemon socket.
[ 7.370321] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 7.377641] systemd[1]: Reached target Encrypted Volumes.
[ 7.382899] systemd[1]: Reached target Paths.
[ 7.519591] EXT4-fs (mmcblk1p2): re-mounted. Opts: errors=remount-ro
[ 7.638079] Loading iSCSI transport class v2.0-870.
[ 7.703880] systemd-journald[1534]: Received request to flush runtime journal from PID 1
[ 7.706677] iscsi: registered transport (tcp)

Debian GNU/Linux 9 BonusCloud-Lite ttyAML0

BonusCloud-Lite login:

qfnuzlr
中学生
帖子: 56
注册时间: 04 11月 2018, 09:38

Re: mgv2000刷的r3300l镜像,结果不能联网,也刷不回盒子了,求助

帖子 qfnuzlr » 14 9月 2019, 17:03

能够告知系统 用户名 密码 进入系统 想办法激活线刷模式 或者还原盒子系统呢
我还有另外一台同样的盒子

头像
二 猫
博士研究生
帖子: 1731
注册时间: 01 11月 2018, 18:34

Re: mgv2000刷的r3300l镜像,结果不能联网,也刷不回盒子了,求助

帖子 二 猫 » 16 9月 2019, 11:20

我让做镜像的给你看一眼
BonusCloud.io

头像
wusheng
硕士研究生
帖子: 260
注册时间: 01 11月 2018, 18:13

Re: mgv2000刷的r3300l镜像,结果不能联网,也刷不回盒子了,求助

帖子 wusheng » 16 9月 2019, 11:33

看日志像是这里出了问题
[ 7.249084] systemd[1]: [/etc/systemd/system/systemd-udevd.service:31] Unknown lvalue 'IPAddressAllow' in section 'Service'
感觉是网卡没识别对

ttl 按住Ctrl+c 插电,输入命令
updata
进入线刷模式
有未记录问题联系https://t.me/wusheng

回复